IC元器件

SN74LVCH16540ADL

参考价格:$1.55-$3.5

Texas Instruments 逻辑 - 栅极和逆变器

SN74LVCH16540ADL 供应商

SN74LVCH16540ADL 属性参数

  • 标准包装:25
  • 类别:集成电路 (IC)
  • 家庭:逻辑 - 栅极和逆变器
  • 系列:74LVCH
  • 逻辑类型:逆变器,缓冲器
  • 电路数:2
  • 输入数:8
  • 特点:三态
  • 电源电压:1.65 V ~ 3.6 V
  • 电流 - 静态(最大值):20µA
  • 输出电流高,低:24mA,24mA
  • 逻辑电平 - 低:0.7 V ~ 0.8 V
  • 逻辑电平 - 高:1.7 V ~ 2 V
  • 额定电压和最大 CL 时的最大传播延迟:3.7ns @ 3.3V,50pF
  • 工作温度:-40°C ~ 85°C
  • 安装类型:表面贴装
  • 供应商设备封装:48-SSOP
  • 封装/外壳:48-BSSOP(0.295",7.50mm 宽)
  • 包装:管件
  • 其它名称:296-8593-5

产品特性

  • Member of the Texas Instruments Widebus™ Family
  • Operates From 1.65 V to 3.6 V
  • Inputs Accept Voltages to 5.5 V
  • Max tpd of 3.7 ns at 3.3 V
  • Typical VOLP (Output Ground Bounce)    <0.8 V at VCC = 3.3 V, TA = 25°C
  • Typical VOHV (Output VOH Undershoot)    >2 V at VCC = 3.3 V, TA = 25°C
  • Ioff Supports Partial-Power-Down Mode Operation
  • Supports Mixed-Mode Signal Operation on All Ports (5-V Input/Output Voltage With 3.3-V VCC)
  • Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors
  • Latch-Up Performance Exceeds 250 mA Per JESD 17
  • ESD Protection Exceeds JESD 22 2000-V Human-Body Model (A114-A) 1000-V Charged-Device Model (C101)
  • 2000-V Human-Body Model (A114-A)
  • 1000-V Charged-Device Model (C101)

产品概述

This 16-bit buffer/driver is designed for 1.65-V to 3.6-V VCC operation, and provides a high-performance bus interface for wide data paths.The 3-state control gate is a 2-input AND gate with active-low inputs so that if either output-enable (OE1\ or OE2\) input is high, all corresponding outputs are in the high-impedance state.Inputs can be driven from either 3.3-V or 5-V devices. This feature allows the use of these devices as translators in a mixed 3.3-V/5-V system environment.Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended.To ensure the high-impedance state during power up or power down, OE\ should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.